Project

General

Profile

Edit History

Getting Started ยป

MVP Development Tasks » History » Version 5

Hammel, 14 Jul 2017 18:00

1 1 Hammel 
h1. MVP Development Tasks
2 





    3
    
    
    
h1. +Monitor+





    4
    
    
    





    5
    
    
    
Note: Touch Display is already supported





    6
    
    
    





    7
    
    
    
h2. Hardware





    8
    
    
    





    9
    
    
    
* Pair Button support (GPIO pin)





    10
    
    
    
** Needs to include LED so we know we're in that mode





    11
    
    
    
* 2G/3G support based on Raspberry Pi phone build





    12
    
    
    
** https://www.graphics-muse.org/wp/?p=5910





    13
    2
    Hammel
    
** Not absolutely required - only used as backup if Internet connection goes down.





    14
    1
    Hammel
    
* Requires Backup Battery Circuit board





    15
    
    
    
** This will handle power input from AC (wall socket) or battery.  Battery should only be backup power!





    16
    
    
    
** http://redmine.graphics-muse.org/projects/ironman/wiki/Hardware_Links (Battery Backup section)





    17
    
    
    
** Needs to set GPIO pin that can be read at boot.





    18
    
    
    
** Needs LED that can be enabled from boot process (not connected to Pair Button) via GPIO to show we're in Pair Mode





    19
    
    
    
* Requires PiDrive for external storage





    20
    
    
    
** http://redmine.graphics-muse.org/projects/ironman/wiki/Hardware_Links (Monitor section)





    21
    
    
    
* Needs WiFi + BLE HAT





    22
    
    
    
** http://redmine.graphics-muse.org/projects/ironman/wiki/Hardware_Links (Monitor Section)





    23
    
    
    
* Needs Enclosure





    24
    
    
    
** PiDrive access door





    25
    
    
    
** Battery access door





    26
    
    
    
** SD card access





    27
    
    
    
** open USB ports access





    28
    
    
    
** Display on top





    29
    4
    Hammel
    
** LEDs visible





    30
    1
    Hammel
    





    31
    
    
    
h2. Software





    32
    
    
    





    33
    
    
    
* Pair Button support on boot





    34
    
    
    
* Write to work like ESP8266 where boot mode can set up AP to allow configuration via mobile device





    35
    
    
    
<pre>





    36
    
    
    
    Handles both Internet wifi setup and sensor network AP config.





    37
    
    
    
    if (pair_button)





    38
    
    
    
    {   





    39
    
    
    
        enable ap only





    40
    
    
    
        enable wifi config in web server





    41
    
    
    
    }





    42
    
    
    
    else





    43
    
    
    
    {   





    44
    
    
    
        enable ap





    45
    
    
    
        enable internet wifi connection





    46
    
    
    
        disable wifi config in web server





    47
    
    
    
    }





    48
    
    
    
</pre>





    49
    
    
    
* New launcher supporting UI design.





    50
    
    
    
* piboxd updates





    51
    
    
    
** needs to support sensor messages (store to sensor location). overwrite with latest message in per-sensor file.





    52
    
    
    
* Battery backup





    53
    
    
    
** On AC power failure, send notifications and continue running.





    54
    
    
    
** power down safely (signal all apps) when battery is low.





    55
    
    
    
* Install





    56
    
    
    
** must format hard drive on firstboot





    57
    
    
    
*** partition 1: app data





    58
    
    
    
*** partition 2: camera recordings





    59
    
    
    
* New apps:





    60
    
    
    
** Sensor config/browse





    61
    
    
    
** Contacts (for notifications)





    62
    
    
    
** Files (for cleanup, status viewing)





    63
    
    
    
** Setup (admin pw, generate keys for sensors)





    64
    
    
    





    65
    
    
    
h1. +Sensors+





    66
    
    
    





    67
    
    
    
Fork "esp8266 project":https://gitlab.com/xarduino/iotdevice





    68
    
    
    





    69
    
    
    
h2. Hardware





    70
    
    
    





    71
    
    
    
* Add pair button + LED





    72
    
    
    
* Add battery power w/ enclosure





    73
    
    
    
* Add door/window sensor





    74
    
    
    
** http://redmine.graphics-muse.org/projects/ironman/wiki/Hardware_Links (Door/Window Alarm section)





    75
    3
    Hammel
    
* Needs enclosure





    76
    
    
    
** Battery access





    77
    
    
    
** Pair button access





    78
    
    
    
** LEDs visible





    79
    1
    Hammel
    





    80
    
    
    
Software:





    81
    
    
    
* Rework esp8266 code to handle new flow diagram.





    82
    
    
    
* If necessary, simplify REST interface.





    83
    
    
    
* Add AES encoding + hash for all messages (inbound and outbound from sensor).





    84
    
    
    





    85
    
    
    
h1. +Management+





    86
    
    
    





    87
    
    
    
* Android:





    88
    
    
    
** Wifi config





    89
    
    
    
*** connect to AP (monitor or sensor)





    90
    
    
    
*** configure network





    91
    
    
    
*** Set admin pw (part of initial setup)





    92
    
    
    
** View sensor status





    93
    
    
    
** Admin





    94
    
    
    
*** Set admin pw (via sensor network only)





    95
    
    
    





    96
    
    
    
* Web UI:





    97
    
    
    
** View sensor status





    98
    
    
    
** Admin





    99
    
    
    
*** Set admin pw





    100
    
    
    
*** gen keys





    101
    
    
    
** Files





    102
    
    
    
*** List





    103
    
    
    
*** Delete





    104
    5
    Hammel
    
** Wifi config





    105
    
    
    
*** Only available if in Pair mode





    106
    
    
    
*** duplicate (but clean up)