Project

General

Profile

Actions
History

Getting Started »

Users Guide » History » Revision 38

« Previous | Revision 38/67 (diff) | Next »
Hammel, 25 Sep 2019 16:09

Ironman Users Guide

This document is under development and is likely not accurate at this time.

In this document the term host system refers to a Linux desktop or laptop that will be used to download and install software onto an SD card.

Overview

Ironman is a home automation project based on the PiBox build system. It supports a Nest-like monitor for controlling Arduino based sensors, cameras and remote voice control.

Design Intent of the Ironman Project
Mark I release is in progress. Mark II and Mark III are future development plans.

Ironman consists of the following components.

Monitor The Nest-like control hub based on a Raspberry Pi 2/3 and the official 7" touchscreen display
Sensors Arduino based devices, such as door alarms and cameras, running code based on a sensor and camera templates for pairing and secure communication with the Monitor
Jarvis A Java application that supports voice control of Monitor managed devices
Controllers Network enabled control of Monitor managed devices

Security

Ironman supports AES encrypted communication with IoT sensors and Jarvis interfaces.

What it is

Ironman is a do-it-yourself system, where you buy the parts and assemble them as described, modifying the provided code to suit your needs and handling flashing and maintenence. Ironman is designed to allow you to build your own home automation system where you specify the devices you want to control and how you want to control them.

What it is not

Ironman is not a product. It is not intended for anyone other than Makers (aka DIY'ers) who like to tinker and see not just how to assemble things but why they actually work.

While the Users Guide is intended to bring up a currently working version of Ironman with limited sensor and camera support, if you aren't prepared to deal with writing code or flashing devices and dealing with electrical circuits then Ironman is not for you.

The Ironman Monitor

The Ironman Monitor runs on a Raspberry Pi 2 or 3 and provides a central hub for management of home automation devices. It uses a 7" touch screen display and a mechanical switch to manage pairing with IoT devices and Jarvis interfaces.

Installation Prerequisites

  • A Raspberry Pi 2 or 3
  • The official Raspberry Pi 7inch touchscreen display
  • The Pi 2/3 requires a V / 2A power supply. For best results, use a power supply rated to at least 5.25V to avoid under voltage conditions. For ease of use the power supply cable should include an on/off switch.
  • A keyboard is required for initial installation. A wireless keyboard should work as will a wired keyboard. The keyboard will not be needed for normal operation but can be helpful in debugging.
  • The Pi 2/3 requires a microSD card that is at least 4GB. A mechanism for using the SD card on your host system is needed, such as an SD card USB adapter or an SD port on your laptop.
  • A mechanical switch, such as a SPDT, should be connected to the Pi GPIOs to allow for pairing the Monitor with IoT Sensors and Jarvis interfaces. The ASCII diagram below describes the setup. The LED is off in normal mode, lit in Config Mode, and off in Pair Mode until something tries to pair with the Pi which then turns on the LED for 3 seconds. Config and Pair mode operations ared discussed in later sections. A Fritzing Diagram (IronmanMonitorSwitch.fzz) is available for this hardware component.
    Ironman Monitor Switch Breadboard
                          ___
   Config/Pair Mode  |---|  Normal Mode
                   --------- 
                  |         |
                   --------- 
connector pins -->  |  |  |  
                    |  |   ------ Not connected
                    |  |
                    |  ----330 Ohm R-----
                    |  |                |
                    |  |  +-----LED------
                    |  |  |
          RPi pin   7  9  13     
         RPi GPIO   4  G  27
  • You will need to have sudo access for your Linux user id.

Generating the SD Card for the Pi

  • Download the RPi 2 Development Platform
    • wget <url>
    • Unpack the archive to a directory called image.
  • Download the Ironman Package Collection
    • wget <url>
    • Unpack the archive to a directory called package.
  • In a terminal window run: dmesg -w
  • Insert the microSD card and note the device name displayed for the newly added card as displayed in the dmesg -w terminal window. It should be something like /dev/sdb or /dev/sde.
  • Kill the dmesg -w command with Ctrl-C.
From the image directory
  • Format the SD card
    • sudo ./mksd.sh -d <device name>
    • where <device name> is the name you noted from the output of dmesg -w.
  • Mount the boot partition from the sd card:
    • sudo mkdir -p /mnt/boot
    • sudo mount <device name>1 /mnt/boot
    • where <device name> is the name you noted from the output of dmesg -w.
  • Install the Development Platform to the SD card
    • sudo ./mkinstall.sh -b /mnt/boot -d <device name>2
    • where <device name> is the name you noted from the output of dmesg -w.
From the package directory
  • Mount the root partition from the sd card:
    • sudo mkdir -p /mnt/root
    • sudo mount <device name>1 /mnt/root
  • Copy the Ironman Package Collection files to /root of the root partition on the SD card
    • sudo cp *.opk /mnt/root/root
Make sure all writes to the SD card have completed
  • sync;sync;sync
Unmount the SD card partitions
  • sudo umount /mnt/boot
  • sudo umount /mnt/root

Remove the SD card from the host system and insert it into the Raspberry Pi 2.

First time boot

Power on the Monitor and wait for it to complete installation. During this time the display may be upside down. Once initial installation is complete the display will be right side up.

Once the display shows two xterm windows it is ready to complete installation. Type the following command to install the Ironman package collection.

opkg install *.opk

Wait for this command to complete, then reboot the system either by power it off and back on or by typing the command 

reboot

The Monitor is now fully installed and ready for use.

First time configuration

Ironman Config UI

Turn the power off and set the Mode switch to Config/Pair, then power the Monitor back on. The LED should light indicating the Monitor is ready to be configured.

Use a smartphone or laptop with wifi to connect to the "ironman" SSID. The default password is ironman1. Then use a browser to connect to the Ironman web UI at 

http://192.168.36.1:1337

The display should be as shown in the adjacent photo. There are two network domains to configure, as described in the following table.

Domain Description
Internet Connection This is how the Monitor will connect to your home network.
Sensors Network This is how the Monitor will communicate with your IoT devices.

After both networks are configured, power off the Monitor and set the Mode switch to Normal, then power the Monitor on. The Monitor is now ready to use with IoT sensors, Jarvis and controllers.

Network configuration

The Monitor's hardware supports WiFi B/G/N networks. However, in order to use the Monitor as both a WiFi client on the local
network and as an Access Point for IoT devices, only G networks are supported by the Ironman software.

Internet Connection

The Internet Connection domain configures the Monitor to connect to your local network.

Field Description
Location Unique name for this monitor, such as Bedroom or Office. This name is used to identify monitors by name via commands from Jarvis or other remote controllers
SSID Network name configured on your router for your local WiFi network.
Security Type of security used on your router. Only WPA2 Personal and WPA2 Enterprise are currently supported.
Password Your router's password, specifically for the SSID entered previously.

The Show Password button will display the password typed in the Password field. By default this button is not enabled, causing the Password field to be hidden using asterisks for each character.

Sensor Network

The Sensor Network domain is used to configure the Monitor's private network used with IoT devices. Data on this network is not routed to the Internet Connection and data from the Internet Connection domain are not routed to the Sensor Network.

Field Description
SSID Network name for this private WiFi network. This name will be hidden on Wifi scans.
Channel Channel to use. Select a channel that has low use in your neighborhood. Only a subset of channels on G networks are available. This will be addressed in future releases.
Password Password IoT devices should use to gain access to the specified SSID.
Static IP An IP address to give the Monitor as it acts as an Access Point. This should be a Class C subnet for the network, which limits the number of IoT devices that can be managed by a single Monitor to 254.

The Show Password button will display the password typed in the Password field. By default this button is not enabled, causing the Password field to be hidden using asterisks for each character.

IoT Sensor

Sensor Types

There is currently only one sensor type: imlightsw (light switch).

The sensor template GIT repository is intended to be used to design additional sensor types, such as door and window alarms, window shade controllers, environment sensors and so forth.

Light Switch

TBD: show screenshot of fritzing diagram for light switch board.

Flashing the firmware

TBD: show screenshot of fritzing diagram for flashing board.

Power On

An IoT sensors must be configured to operate on the same network as the Monitor's Sensor Network. Once this has been done the IoT sensor and the Monitor can be paired. An IoT device can only be paired with a single Monitor.

Configuring an IoT Device Network

  • Set the Mode button to Config.
  • Power on the IoT device.
  • TBD

Pairing with a Monitor

  • With the Monitor running, set the Monitor Mode switch to Pair.
  • Power on the IoT Sensor and wait for it to pair with the Monitor. When it's done, the LED will light for 3 seconds.
  • Disable the Mode switch on the Monitor.
WARNING!
Leaving the Mode switch turned to Pair will allow random devices to attempt to pair with the Monitor. This is a security risk. The Mode switch should only be set to Pair long enough to pair with an IoT device.

Jarvis

Prerequisites

Pairing with a Monitor

  • With the Monitor running, set the Monitor Mode switch to Pair.
  • TBD

Supported Commands

Addendums

Ironman Apps

App Contents Description
imcore Package that updates a PiBox Development Platform for use with Ironman. Includes network configuration updates and other config files.
imwww Contains two web servers
imwww Provides network configuration interface for Monitor
imrest Provides IoT/Jarvis REST API. Updates /etc/ironman directories with registrations.
imgpio Command line tool for querying GPIO pins using syfs interface.
launcher Ironman specific launcher that adds clock interface to front panel.
pisensors Provides UI for managing sensors. Uses inotify to watch for changes to /etc/ironman/iot directory.
picam Generic console camera interface (same as PiBox media systems)
Misc appmgr, piboxd, omxplayer, pmsui, psplash, mjpg-streamer Same packages as in PiBox media system, unmodified

Source Code Repositories

  • PiBox
    • Development Platform
    • appmgr
    • mjpg-streamer
    • omxplayer
    • piboxd
    • picam
    • pmsui
    • psplash
  • Ironman
    • launcher
    • monitor
    • pisensor
    • www
  • Arduino
    • Sensor Template (imlightsw)

Fritzing Models

Networking Internals

wlan0

* This interface is used for configuration of the Monitor.
* Configured on the 192.168.36.0 subnet.
** See /etc/network/dhcpd.conf.aponly

uap0

* This interface is used as an access point for IoT devices.
* Configured on the 192.168.3.0 subnet.
** See /etc/network/dhcpd.conf.uap and dhcpd.conf.uap.tmpl
** The template is used to change the base subnet through the web interface.
** The SSID is _ironman_.

Pair Button Usage

Pair/Config button is GPIO 4 (RPi pin 7)
Pair/Config LED is GPIO 7 (RPi pin 13)
    LED should only be lit on boot if button is enabled (in Config mode).
        In this case, we're in Config Mode to configure the networks.
        The web server (imwww) is on SSID _ironman_ at 192.168.36.1:1337.
    LED is off on boot if button is disabled (in Pair Mode).
    If in Pair Mode
        Start hostapd for aponly
        Start dhcpd for aponly on wlan0
        Start imrest web service on port 8165 for IoT devices and Jarvis interfaces.
    If in Config Mode
        Start wpa_supplicant on wlan0
        Create uap0 device as virtual device on wlan0
        Start dhcpd on uap0
        Start hostapd on uap0
        Start imwww for network configuration of the Monitor.

Monitor IoT Directories

/etc/ironman/iot        Registration directory for IoT devices
/etc/ironman/jarvis        Registration directgory for Jarvis interfaces

Updated by Hammel about 5 years ago · 38 revisions